News
Your location:
Homepage
>
>
>
Cleaning and maintenance of sponge cutting machine equipment

Cleaning and maintenance of sponge cutting machine equipment

  • Categories:Industry News
  • Author:
  • Origin:
  • Time of issue:2021-09-26
  • Views:0

(Summary description)How should the cleaning and maintenance of the sponge cutting machine equipment be carried out? The following is a detailed introduction for everyone.

Cleaning and maintenance of sponge cutting machine equipment

(Summary description)How should the cleaning and maintenance of the sponge cutting machine equipment be carried out? The following is a detailed introduction for everyone.

  • Categories:Industry News
  • Author:
  • Origin:
  • Time of issue:2021-09-26
  • Views:0
Information

How should the cleaning and maintenance of the sponge cutting machine equipment be carried out? The following is a detailed introduction for everyone.

Electrical equipment should always be kept clean to prevent oil, water and dust from entering.

When there is a circuit short circuit, it should be replaced with a fuse of the same capacity, tin and silver wire can be used, and it is recommended not to use copper wire as a substitute.

Rotating motors use rolling bearings, and the bearings should be cleaned (with kerosene or diesel) every other month and replaced with clean grease. Gears, sprockets, etc. should be cleaned and lubricated before leaving get off work every day.

When motors and electrical appliances have been parked for too long in the humid season (more than 1 month later) and used again, the electrical insulation should be re-examined and must be dehumidified, that is, the motor should be idling when the voltage is reduced to 1/3 of the rated value. Hours, in order to gradually expel the moisture, and then run at full pressure to ensure that there is no worry.

Note that the mechanical grounding must be good. If the end surface of the grounding screw is oily or rusted, it should be cleaned at any time.

Pay attention to whether the exposed hoses and wires are misaligned, broken, or damaged. (Sponge cutting machine)

Always check the sensitivity of each contact and interlocking device.

Use mechanical and electrical equipment in accordance with the provisions of the instruction manual.

Scan the QR code to read on your phone

Related products

 Multifunctional horizontal and vertical cutting center
Multifunctional horizontal and vertical cutting center
V series cutting machine is an ultra-high cost-effective equipment.
 Precision vertical modeling cutting center
Precision vertical modeling cutting center
V series cutting machine is an ultra-high cost-effective equipment.
 Precision horizontal modeling cutting center
Precision horizontal modeling cutting center
V series cutting machine is an ultra-high cost-effective equipment.
 Modeling and cutting center of precision horizontal turntable
Modeling and cutting center of precision horizontal turntable
V series cutting machine is an ultra-high cost-effective equipment.
 Efficient and multifunctional horizontal and vertical cutting center
Efficient and multifunctional horizontal and vertical cutting center
C series cutting machine is an ideal model for efficient cutting, with strong cutting ability, "flying" cutting speed, high stability, high quality processing, low operating cost and high adaptability.
 Efficient vertical modeling cutting center
Efficient vertical modeling cutting center
C series cutting machine is an ideal model for efficient cutting, with strong cutting ability, "flying" cutting speed, high stability, high quality processing, low operating cost and high adaptability.
 Efficient horizontal modeling and cutting center
Efficient horizontal modeling and cutting center
C series cutting machine is an ideal model for efficient cutting, with strong cutting ability, "flying" cutting speed, high stability, high quality processing, low operating cost and high adaptability.
 Automatic vertical double cutter block cutting center
Automatic vertical double cutter block cutting center
The new member of C series is a super cost-effective cutting and trimming, which provides flexible solutions and good performance for batch cutting of sheets.
 NC horizontal and vertical double line cutter cutting center
NC horizontal and vertical double line cutter cutting center
T series cutting machine is an ultra-high cost-effective equipment, providing a flexible solution for cutting geometric shapes of harder materials, and has excellent performance in cutting various shapes.
ZHIGU

Nantong Zhigu CNC Machinery Co., Ltd

 

24-hour technical service hotline

Tel:+86-15190888255

Tel:+86-513-87550889

Sales Hotline:

+86-18101489666(Manager yuan)

+86-15366388255(Manager shen)

Technical Hotline:15190888255 (She Manager)

E-mail:450971650@qq.com   zgsk@ntzgsk.cn

Address: No. 396, Zhongshan West Road, Rugao City, Jiangsu Province

Focus on us

ZHIGU

Copyright © Nantong Zhigu CNC Machinery Co., Ltd.  苏ICP备15036056号-1       www.300.cn